Software Version History Highlights—
System 930 Telephony Simulator E1 Version
Screen 4: Fixed automatic disconnect after second party flash
transfers to and from a busy station and first party hangs up.
Screen 4: Fixed flash transfer to a descending OPS extension number.
Version 1.54: Screen 1: Added switch
emulation H11 CHANNEL PASS-THRU.
Version 1.53: Authorization
Configuration: Added Revision FM board.
Version 1.52: Screen 17: Added
selection local dial tone.
Version 1.51: Screen 4: Added support
for 938A analog card.
Version 1.48: Screen 25: Fixed Called
Mode to correctly display selections when spacebar is pressed.
Version 1.47: Screen 17: Fixed network
side of ETSI E1 ISDN to send connect ack after receiving a quick
connect without a channel ID.
Version 1.46: Screen 17: Added
selection allow FXO/SAO signaling.
Version 1.45: Screen 23: Added variable
audio threshold to S and V commands.
Version 1.44: Screen 6: Allow bracketed
inbound match ranges to contain multiple digits.
Screen 8: Allow bracketed outbound prefix numbers to contain
Screen 25: Added forced disconnect time to 939 card general
Version 1.43: Added call waiting.
Version 1.42: Added analog Caller ID
which is supported by the 938 card.
Version 1.40: Screen 18: Show CRV and
CID in decimal instead of hex. Fixed GR-303 CRV to show the call
reference divided by eight.
Version 1.39: Added support for
revision G processor card.
Version 1.38: Changed GR-303 Channel ID
to start from interface 1.
Screen 18: Retain data capture upon power up.
Screen 21: Fixed bug that prevented call generator from working when
maximum number of calls is blank on the Call Generator Configuration
– Analog Ports screen.
Version 1.37: Changed Euro ISDN overlap
dialing to send the called number IE instead of keypad IE and
concatenate digits on the receive side.
Screen 3: Added calling name to NI-2, 4ESS, and EURO ISDN.
Screen 21: Added maximum number of calls to the call generator.
Version 1.36: Screen 1: Added GR-303
Screen 3: Renamed caller to calling. Added calling name to 5ESS and
Screen 21: Added random called number groups to the call generator.
Version 1.35: Screen 25: Added new
screen to configure the 939 analog card.
Version 1.34: Screen 3: Added random and sequential calling numbers.
Screen 17: Added send channel ID in first message only. Added
increment after each call to cause code
Screen 24: Added new screen for time and date configuration.
Version 1.33: Screen 18: Increased data capture to 10
Screen 21: Fixed call generator to start correctly the first time a
new software version is installed. Fixed
internal call ID so that connected calls are not disconnected after
16384 additional calls.
Version 1.32: Screen 1: Added GR-303 CSC switch emulation
to T1 version. Added QSIG switch emulation to E1 version. Added NFAS
signaling to E1 and T1 versions. Added loop disconnect to T1 loop
start FXO and SAO.
Screen 7: Allow en-bloc or overlap dialing when switch emulation is
T1 RBS network or user side.
Screen 8: Added Z to allow match for no outbound prefix.
Screen 11: Added any digital interface or analog port to audio
monitor source selection.
Screen 18: Added ISDN message types to data capture.
Screen 20: Added restart system to save/restore action.
Screen 22: Added connect action counters.
Screen 23: Added new screen for connect action configuration. Added
ability to route incoming calls to
Version 1.31: Screen 6: Added Z to allow match for no
inbound called number.
Version 1.30: Screen 2: Added new selection: Send
D-channel status to T1 ISDN.
Screen 4: Added new selections: Receive loss and reference tone.
This coincides with a change to 938
card firmware that inserts a –6 dB loss in the audio level sent to
analog ports required by V.90 (56 k) analog modems.
Screen 7: Changed access digits to be flexible instead of hard coded
to 8 and 9.
Version 1.29: Screen 7: Allow only en-bloc dialing when
switch emulation is T1 RBS network side.
Screen 9: Added redirect ACD overflow action.
Screen 18: Enhanced call detail records for analog ports.
Former screen 19: Split call generator into screen 21 and 22.
Screen 21: Added running – until no connect to call generator mode.
Screen 22: Extended call counters to 32 bits.
Version 1.28: Fixed DTMF digit transfer from analog
ports. Fixed bearer information element when redirecting from RBS to
Screen 4: Added signaling method to individual analog ports.
Screen 18: Added call detail records for analog ports.
Version 1.27: Increased minimum time between analog port
Version 1.26: Increased analog port on-hook debounce to
Screen 21: Added call routing to analog port call generator.
Version 1.25: Added support for 932 processor card
revision F. This card contains a battery
powered clock and selectable A-law/mu-law audio monitoring and
recorder/announcer. Software is
backwards compatible with 932 processor card revision C.
Screen 2: Added ability to change ISDN channel service on the fly.
Fixed ISDN channel disabled to place channel out of service upon
layer 2 startup.
Screen 9: Changed least busy ACD hunt method to clockwise circular.
Screen 17: Added selectable exclusive / preferred channel ID.
Screen 18: Added current year, month, and time zone.
Version 1.24: Fixed intermittent response to ISDN
messages. Fixed system reset due to
unacknowledged service messages. Fixed ACD queuing problem due to
version 1.17 changes. Improved
call generator burst mode.
Screen 4: Added configurable alerting time. Allow analog port
extensions to begin with 7.
Screen 7: Changed explicit channel access digit from 7 to *.
Screen 18: Added text to show ISDN transfer capability after bearer
capability information elements.
Added text to show ISDN channel number after channel ID information
Version 1.23: Screen 11: Improved audio monitor.
Version 1.22: Fixed multirate to connect channels when
bearer capability information element length is 2.
Screen 3: Allow call generator to overlay calling number.
Screen 10: Improved redirect by copying display, transit network
selection, low layer compatibility, high layer compatibility, and
user-user ISDN information elements from incoming to outgoing call.
Screen 11: Improved fixed channel or port on audio monitor.
Screen 12: Added configurable password reminder.
Screen 17: Added configurable multirate slot assignment.
Screen 18: Add milliseconds to ISDN data capture timestamp. Show
call state name in RBS data capture.
Screen 21: Allow sequential DTMF numbers in the call generator
Screen 22: Save call generator historical data during power loss.
Version 1.20: Improved analog disconnect synchronization
with 938 card.
Version 1.19: Screen 2: Fixed RBS exclusive channel
operation and added it to T1 ISDN.
Version 1.18: Fixed T1 RBS loop start signaling. Fixed
user side 5ESS custom to accept unknown type of number. Added
sending complete information element to Euro ISDN setup messages
during en-bloc dialing. Fixed numerous problems in redirect.
Screen 2: Added selection to send T1 ISDN service messages upon
establishment of layer two.
Screen 6: Added selection to route incoming calls to voice message
Screen 7: Added selection for whether analog ports use en-bloc or
Screen 12: Added selection for automatic startup of ISDN layer two.
Added selection for ISDN channel ID format. This allows the system
to work with products that accept number format only.
Screen 18: Decode IA5 characters such as called number instead of
showing them in hex on data capture screen. Fixed display of single
byte information elements such as sending complete.
Screen 22: Added incoming message count to call counter screen.
Version 1.17: Changed redirect to echo incoming bearer
capability information element rather than use screen 17 settings.
Screen 17: Added setup bearer rate for testing multirate calls.
Accidentally changed channel ID format in ISDN proceeding messages
to send slot map format. Added selection to use last 3 digits of
for testing cause codes.
Version 1.15: Screen 17: Added selection do not send
channel ID. Fixed network side Euro ISDN
to accept messages without channel ID. Added selection do not send
ISDN proceeding message and do not send ISDN alerting message to
test ISDN quick connect.
Version 1.12: Combined T1 ISDN and T1 RBS into a single
Version 1.10: First release of Euro ISDN. Updated tone